97778 | Banks Ram-Air Transmission Pan for 2020-2026 Ford F-250-550 6.7L Diesel with 10R140 Transmission

Transmission Pan Gasket:
Ford Part #

Filter Kit:
Ford Part #

1. The day before your install, locate the 15mm Drain Extension Fitting.

2. Apply some red Loctite to the threads before installing.

3. With a 15mm socket, torque the fitting to 15 ft-lbs.

Banks recommends allowing for a full 24 hours for the sealant to cure before installing the pan.

1. Raise the truck on a lift to provide ample access to the oil pan and the area you will be working with.

2. If using a lift, a support stand is also recommended.

1. Start by locating the heat shield on the passenger side of the transmission

2. Remove the three 10mm bolts that hold the heat shield.

3. Take note, the factory transmission pan has five 13mm bolts….

…and fifteen 10mm bolts.

When installing the Banks Ram-Air Transmission Pan, you will be use the twenty supplied 10mm bolts.

4. In no particular order, begin removing the 13 and 10mm bolts.

Support the pan as you reach the end to avoid unnecessary stress on the bolts or sudden leaks as the pan breaks free.

5. Carefully lower the pan from the truck. Take care as it will be full of fluid.

6. Additional fluid will continue to drain from the bottom of the transmission and filter. Be sure to catch all the old fluid in a proper container.

1. With an 8mm socket, remove the two bolts that secure the filter onto the transmission.

2. Wiggle the filter free from the pickup tube.

3. Take note of the transmission filter collar, as it may stick to the filter upon removal.

4. Reinstall it onto the transmission, or replace it with a new one if your filter kit contains a new one.

5. Maneuver the new filter into position.

6. Secure the filter with the factory 8mm bolts.

1. Take note of the two alignment tabs on the gasket and pan, this will help align the gasket into the groove

2. Take care not to stretch the gasket around the pan, it should fit right in with no extra slack by the end

X. Locate the two small spring clip dowels.

X. Insert the two small spring clip dowels into the pan.

X. Insert them by hand until they bottom out.

3. Locate the smaller face sealing bolt.

4. With a 10mm socket, snug it down by hand.

This port will be used after installation to check the correct fluid level.

5. Locate the larger Banks Magnetic Drain Plug.

6. With a 15mm socket, snug it down by hand.

7. Locate and install the 1/4″ AN fitting. Secure it in place with a 3/16th hex key. It has sealant pre-applied.

Alternatively, if running an auxiliary temperature sensor, it can be threaded in here.

1. Bring the assembled Ram-Air Transmission Pan back to the truck.

2. While supporting the bottom of the pan, install one bolt on one side.

3. And install a second bolt on the other side to keep the pan in place.

4. Next, begin installing the remaining eighteen 10mm bolts. Thread them loosely until they just seat.

6. Locate the four billet washers and 4 remaining 10mm bolts for the Ram-Air Scoop.

7. Each bolt will use a washer with the narrow end pointing towards the threaded end.

8. Raise up the Ram-Air scoop, and begin threading the bolt/washer combos to the sides and bottom by hand.

9. Secure them in place with an 8mm socket.

1. On F-250 & F-350 trucks, locate the transmission fill plug on the rear driver side.

2. With the vehicle OFF, remove the plug with a 10mm hex.

3. For the initial first fill, add 12qts of ATF via the drain plug. Reinstall the fill plug when complete.

4. Lower the truck and take it for a brief test drive.

This is to work the new fluid into the transmission and raise the internal temperature to between 195-215°F.

5. After returning, raise the truck back up on the lift, but keep the engine running.

6. Note: Drain Plug will be HOT

Check the correct level by removing the 10mm fill check plug. The fluid and plug will be HOT. If no fluid is dripping from this port, add additional ATF via the fill plug until it does.

7. Reinstall the 10mm fill check plug when complete.